ASME A112.18.1-2012 pdf free download.Plumbing supply fittings
This Standard covers plumbing supply fttings and acessories located between the supply stop and the terminal ftting, inclusive, as follows:
(a) automatic compensating valves for individual wall-mounted showering systems;
(b) bath and shower supply ftings;
(c) bidet supply fttings;
(d) clothes washer supply fttings;
(e) drinking fountain supply fttings;
(f) humidifier supply stops; .
(g) kitchen, sink, and lavatory supply fttings;
(h) laundry tub supply fting,
(i) lawn and sediment faucets;
(g) metering and slf-closing supply ftings;
(k) shower heads, hand-held showers, and body sprays; and
(l) supply stops.
This Standard does not cover
(a) plumbing waste ftings, which are covered by ASME A112.18.2/CSA B125.2;
b) other devices (e.g. temperature-actuated in-ine mixing valves), which are covered by CSA B125.3 or other plumbing product Standards; and
(c) flexible water connectors under continuous pressure, which are covered by ASME A112.18.6/CSA B125.6.
1.3Except for push-fit ftings, this Standard does not cover pipes and tubes or pipe and tube ftings.
1.4 In this Standard, “shall” is used to express a requirement, i.e, a provision that the user is obliged to satisfy in order to comply with the standard;“should” is used to express a recommendation or that which is advised but not required; “may” is used to express an option or that which is permissible within the limits of the standard; and “can” is used to express pssibility or capability.
Notes accompanying dauses do not include requirements or altrnative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.
Notes to tables and figures are considered part of the table or figure and may be witten as requirements.
Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.
1.5 SI units are the units of record in Canada. In this Standard, the inch/ pound units are shown in parentheses.
The values stated in each measurement system are equivalent in application; however, each system is to be used independently. Combining values from the two measurement systems can result in non-conformance with this Standard.
2 Reference publications
This Standard refers to the fllowing public ations, and where such reference is made, it shall be to the edition listed below, including all amendments published thereto.
ASSE/ASME/CSA Group (American Soclety of Sanitary Engineering/ The American Society of Mechanical Engineers)
ASSE 1016-201 1/ASME A112.1016-2011/CSA B125.16-11
Performance requirements for outomatic compensoting valves for individual showers and tub/shower combinations
ASME/CSA Group (The American Soclety of Mechanical Engineers)
ASME A112.18.2-201/CSA B125.2-11
Plumbing waste ftings
ASME A112.18.6 2009/CSA B125.6-09.
Flexible woter connectors
ASME (The American Socliety of Mechanical Engineers)
A112.1.2-2004
Air Gaps in Plumbing Systems (For Plumbing Fixtures and Woter-Connected Receptors)
A112.18.3-2002 (R2008)
Performance Requrements for Backlow Protection Devices and Systems in Plumbing Fixture Fitings
B1.20.1-1983 (R2006)
Pipe Threads, General Purpose, Inch
B1.20.7-1991 (R2008)
Hose Coupling Screw Threads, Inch
B16.18- 2001 (R2005)
Cast Copper Aly Solder Joint Pressure Fltings
B16.22-2001 (R2005.)
Wrought Copper and Copper Alov Solder Joint Pressure Fttings
B16.26-2006
Cast Copper Aloy Fttings for Flared Copper Tubes
PTC 19.2-1987 (R2004)
Pressure Measurement
PTC 19.5-2004
Flow measurement
CSA Group
CAN/CSA- B64 Series-07
Backflow preventers and vacum breakers
ASSE (American Society of Sanitary Engineering)
1019-2004
Vacum Breaker Wall Hydrants, Freeze Resistant, Automatic Draining Type
1061-2006
Removable & Non-Removable Push-Fit Fttings
ASTM International (American Society for Testing and Materials)
B117-07a
Standard Practice for Operating Salt Spray (Fog) Apparatus
B368-97(2003)e1
Standard Method for CopperAccelerated Acetic Acid-Salt Spray (Fog) Testing (CASS Test)
B380-97(2008)e1
Standard Test Method of Corrosion Testing of Decorative Electrodeposited Coatings by the Corrodkote Procedure
B571-97(2008)e1
Standard Practice for Qualitative Adhesion Testing of Metallic Coatings
D968-05e1
Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive
D3359-09e2
Standard Test Methods for Measuring Adhesion by Tape Test
E29-08
Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
G85-02e1 .
Standard Practice for Modified Salt Spray (Fog) Testing
ISA (Instrumentation, Systems, and Automation Society)
ANSI/ISA-75.02-2008
Control Valve Capacity Test Procedures.ASME A112.18.1 pdf download.ASME A112.18.1-2012 pdf free download
